Menu
Your Cart

Polk Audio 200.4 High performance 4-channel mobile audio amplifier

Polk Audio 200.4 High performance 4-channel mobile audio amplifier
DISCONTINUED
Polk Audio 200.4 High performance 4-channel mobile audio amplifier
RM985.00
  • Stock: DISCONTINUED
  • Model: PA200.4
  • Weight: 6,500.00g
  • SKU: PA200.4
Pure Performance.
The PA200.4 features a high-speed MOSFET switching power supply and high current bipolar output transistors for maximum voltage and high current to your speakers or subwoofers. A double layer fiberglass epoxy printed circuit board provides more rigidity and less shrinkage, with plated through-holes instead of jumpers, for twice the amount of component contact area. This very efficient layout packs more circuitry, with tighter component tolerances, into a smaller circuit board for a smaller overall amp footprint.

PA200.4 Features:
50 Watts x 4 (2 ohm) or 35 Watts x 4 (4 ohm) continuous power in 4 channel mode. 100 Watts x 2 (4 ohm) continuous dual bridge mono/2 channel mode.

80 x 4 (2 ohm) dynamic power.

CEA-2006 compliant specifications for true, accurate power ratings.

4-channel, dual bridge-mono (2-channel), or dual simultaneous stereo/mono operation provide a variety of configurations and setups: 4-channel for front and rear speakers; 2 speakers and a sub; as 2 subwoofers; or as 2 subs and 4-channels in passive-tri mode.

2 ohm stable 4-channel operation.

6-way Smart System Protection (SSP) circuits: Power and ground-reversal protection, thermal and short protection, current overdraw and low impedance protection circuits with auto-standby mode ensure safety, reliability and durability.

Anodized extruded brushed-aluminum cover and textured end caps for maximum heat dissipation.

Cast aluminum textured end caps for optimized heat dissipation and hiding of connectors. Solid aluminum logo and model panel back lit in cobalt blue.

Selectable 12 dB/octave high or low-pass crossover. Defeatable for full range (flat) operation.

Switchable 8 dB bass boost at 40Hz for extra bass thump.

Variable input gain optimizes match with different signal sources (250mv to 7.5V).

RCA outputs (front channels only)- for easy daisy chaining of other amplifiers.

Mounting hardware with rubber isolation grommets and extra fuse included.

Light bar/fan output-Connect an optional LED light bar or cooling fan for custom installations.

Multi-color status LED gives instant information on amplifier operation.

Specifications

Electrical
Total Frequency Response: 20-20 KHz
Signal-to-noise (Referenced to rated power): 90 dBA
Protection Circuitry: 1 x 30 amp fuse, Power and Ground-Reversal Protection, Thermal and DC offset
Subsonic Filter: No

High Pass Filter
Filter Slope: 12 dB/octave
Filter Frequency: 80 Hz

Low Pass Filter
Filter Slope: 12 dB/octave
Filter Frequency: 80 Hz
Effective Damping Factor: >100
Input Impedance: 20.0000 k ohms
Max Sensitivity: 250 mV to 7.5 dB

Dimensions
Product Weight (each): 10.00 pounds
With Panels
Height: 2 16/25" (6.71cm)
Width: 12 1/2" (31.75cm)
Depth: 10 1/4" (26.04cm)

Amplifier Specs
Channels: 4
Bass Boost Characteristics: +8 dB @ 40 Hz Hz
12V & Ground Cable Gauge: 10 AWG Minimum

Amplifier Power Specs
RMS Power at 14.4V
Watts per channel NOT bridged @ 1 kHz
4 ohms: 45 watts
2 ohms: 50 watts
Watts per channel bridged
4 ohms: 100 watts
Dynamic Power at 14.4V
Watts per channel NOT bridged @ 1 kHz
2 ohms: 80 watts

Write a review

Note: HTML is not translated!
Bad Good